On top of our basic coverage, we offer: Basic Coverage 36 months/36,000 miles (all components other than normal wear and maintenance items). Powertrain Coverage 60 months/60,000 miles (engine, transmission/transaxle, front-wheel-drive system, rear-wheel drive, seatbelts and airbags). Rust-Through Coverage 60 months/unlimited miles (corrosion perforation of sheet metal). Emissions Coverage Coverages vary under Federal and California regulations.
Refer to applicable Warranty & Maintenance Guide for details. On top of our basic coverage, we offer: Hybrid-Related Component Coverage Hybrid-related components, including the HV battery, battery control module, hybrid control module and inverter with converter, are covered for 8 years/100,000 miles. The HV battery may have longer coverage under emissions warranty. Refer to applicable Warranty & Maintenance Guide for details.
Powertrain Coverage 60 months/60,000 miles (engine, transmission/transaxle, front-wheel-drive system, rear-wheel drive, seatbelts and airbags). Rust-Through Coverage 60 months/unlimited miles (corrosion perforation of sheet metal). Emissions Coverage: Coverages vary under Federal and California regulations. Refer to applicable Warranty & Maintenance Guide for details.
For accessories purchased at the time of the new vehicle purchase, the Toyota Accessory Warranty coverage is in effect for 36 months/36,000 miles from the vehicle's in-service date, which is the same coverage as the Toyota New Vehicle Limited Warranty. For accessories purchased after the new vehicle purchase, the coverage is 12 months, regardless of mileage, from the date the accessory was installed on the vehicle, or the remainder of any applicable new vehicle warranty, whichever provides greater coverage, with the exception of car covers.
Car covers are warranted for 12 months from the date of purchase and do not assume any coverage under the Toyota New Vehicle Limited Warranty. Each Toyota Certified Used Hybrid and Vehicle comes with a 12-month/12,000-mile limited comprehensive warranty from date of certified purchase. Each Toyota Certified Used Hybrid is covered by an 8-year/100,000-mile Factory Hybrid Vehicle Battery Warranty, including the HV battery, battery control module, hybrid control module and inverter with converter. The HV battery may have longer coverage under emissions warranty.
Click on the winch family to see all the manuals for each model of winch. Have a question or don't see yours? We're ready to help. Superwinch EXP Series EXP Owners Manual Superwinch Talon Series Talon 9.5/12.5 Spare/Replacement Parts Guide Talon Technical Data Guide (9.5/12.5 all versions) Talon Technical Data Guide (1.
Refer to applicable Owner's Warranty & Maintenance Guide for details. Additionally, all Toyota Certified Used Vehicles are backed by a 7-year/100,000-mile Limited Powertrain Warranty (from original date of first use when purchased as new). We also add a 1-year 24-hour Roadside Assistance Plan (from original date of TCUV purchase). For the enhanced peace of mind of an available Extended Vehicle Service Agreement, please visit. Here are a few of the features and benefits of the Toyota Certified Limited Powertrain Warranty:. Valid at over 1400 Toyota dealerships in the U.S.
And Canada. Transferable at no cost for added resale value. Travel protection. Substitute transportation. Toll-free line assistance The following major components are covered by the Toyota Certified Limited Powertrain Warranty:. Engine Components.
Manual Transmission. Automatic Transmission. Axle Assembly Components. Hybrid Components.
HexMag, Inc.308/SR-25 10 Round Magazines Sold by Sentry Products Group Product Safety Warning and Recall Notice Consumer safety is the first priority. Please contact HexMag immediately to facilitate the replacement of your.308/SR-25 10 Round Magazines at the factory at no charge to customers. Recalled Risers will not be returned. DO NOT use your.308/SR-25 10 Round Magazines unless it has been assembled with the new replacement riser! Any unintended discharge has the potential for causing injury or death. HOW TO DETERMINE IF.308/SR-25 10 ROUND MAGAZINES NEEDS REPLACED: Load your magazine with.308 cartridges of the until the magazine can no longer accept any additional cartridges. Remove each cartridge contained in the magazine and count the total number of cartridges that were capable of fitting within the magazine. If that number exceeds 10, the magazine is subject to this recall. Alternatively, if your.308/SR-25 10 ROUND MAGAZINES contains a black riser (depicted at left), then your magazine is subject to this recall.
REPLACING YOUR AFFECTED PRODUCT: If you own a magazine that is subject to this recall, Sentry Products Group will provide a replacement magazine configured with the replacement riser (depicted at right) and ship it to you at no additional cost. Contact HexMag immediately! They will ask for your Name, Address, Telephone Number, Number of Magazines, and provide to you an RMA # for return and tracking purposes.
Once you have been provided an RMA #, you will need to remove the riser from your affected product, and send the affected riser to:SENTRY Products Group, LLC, 2929 S. Cole Road, Boise ID 83709. Please discard the remaining components of the affected magazine. Upon receipt, Sentry will return a new replacement magazine. CONTACT SENTRY (Monday – Friday, 8:00 AM to 5:00 PM EST) Email: [email protected] Recall Hotline: 877.726.7328 FAX: 757.689.6066. KelTec Firearms has announced a voluntary recall of certain Sub-2000 ( aka Sub2k) pistol-caliber collapsible rifles due to a potentially dangerous condition. While, thankfully, we escaped our personal firearms being subject to this condition, many others are still out there.
Sub-2000 owners can check to see if their firearm is subject to the recall by entering their serial number(s) on or by viewing the. From KelTec: ATTENTION IMPORTANT SUB-2000 SAFETY RECALL NOTICE We have recently identified an issue with the heat treatment of certain steel tubes received from a third‐party supplier from which the barrels for a limited number of Kel‐Tec SUB‐2000 rifles were manufactured. This could potentially cause the barrel to rupture when a cartridge is fired and could result in serious personal injury. The safety of our customers is our primary concern, so Kel‐Tec has voluntarily initiated this recall because of the possibility of a barrel rupturing. This recall only affects a portion of SUB‐2000s that were manufactured in 2017.
All costs associated with the recall of your firearm shall be covered by Kel‐Tec. Georgia-based Liberty Suppressors yesterday a recall on a portion of their Leonidas integral suppressor line: Liberty Suppressors has noticed a problem with some of our Leonidas integral suppressors.
The problem stems from a running change with the Seekins Precision iRMT-R upper receiver units.At some point in the last year, Seekins Precision made a running change to the style of retaining nut used on these uppers and we did not realize it, until today. If you have one of our Leonidas integrals with the barrel nut as shown below, please discontinue use of the upper and call us to get it returned and updated free of charge. Use of this upper in this condition could cause catastrophic failure. Please call us to get your upper updated immediately.
Please see the attached images for clarification of whether your upper is affected or not. David Saylors Liberty Suppressors. Battenfeld Technologies, Inc. (BTI) has announced a recall involving its M&P AR-15 Rifle Lower Parts Kit Complete, an aftermarket parts kit. This recall does NOT include and is not related to Smith & Wesson (S&W) factory produced complete M&P rifles. The M&P AR-15 Rifle Lower Parts Kit Complete, identified as Item No.
110114, consists of the parts necessary to build a complete lower receiver for an AR-15 style modern sporting rifle. BTI is recalling all kits distributed prior to September 12, 2017, which do not exceed more than 4,700 kits. Kits sold during this time period may have been supplied with an incorrect hammer, which may lead to a failure of certain rifles to function as intended, including a potential risk of an unintended discharge.
These kits were available for purchase online and through select retailers and distributors, including Turner’s Outdoorsman, Cabela’s, among others. If you purchased a product advertised as an M&P AR-15 Rifle Lower Parts Kit Complete (Item No. 110114) during the referenced timeframe, please contact BTI at (877) 416-5167 or [email protected] to arrange for the return of your kit and the issuance of a replacement hammer.
While you are awaiting the replacement hammer, any rifle assembled with an M&P AR-15 Rifle Lower Parts Kit Complete should NOT be used. We’ll leave the discussion of Sig Sauer’s P320 issues, differences between the military contract pistols and those sold to consumers, the “I Told You Sos,” “What Were They Thinkings,” and the Recall vs Upgrade debates to our readers in the comments section below and on the. There are now plenty of videos and discussions going on around the internet that most people by now know that the Sig Sauer P320 can be caused to fire unintentionally (that is, without an intentional, manual trigger pull) by being dropped at a certain angle or even by giving it a firm whack on the behind. The company has temporarily suspended shipment of the P320 from the factory while they “ramp up to implement changes” related to the condition. Sig that they would be issuing a voluntary upgrade to the P320 to address concerns and the details of that upgrade program -which will include “ an alternate design that reduces the physical weight of the trigger, sear, and striker while additionally adding a mechanical disconnector” – are now available.
The official is up on the Sig Sauer website along with instructions on how to upgrade your pistol at no cost to you. Owners of affected pistols (US domestic commercial customers) may enter their serial number on the website to begin the upgrade process and then Sig “ will contact you regarding the best method for you to get your P320 pistol to them.” Sig continues to maintain that the P320 pistol is safe in its current configuration on the “voluntary upgrade” page, saying that their “ mechanical safeties are designed to augment, not replace safe handling practices.
Careless and improper handling of any firearm can result in an unintentional discharge.” Take from that statement what you wish, from a company selling defensive firearms that may be used by open or concealed carry practitioners and law enforcement officers, often in the worst of situations that may include physical confrontations and attacks, sweat, blood, dirt, darkness, and other less than ideal conditions. This reminds me of the chair lift commercials on TV that advise the old folks to avoid breaking their hips with this weird old trick “ just don’t fall!” Just don’t drop or roughly handle your pistol and you won’t accidentally get shot by it; it’s just that easy! The company continues to go on about how they included (likely legally obligated) language in the user manual that it might go off if dropped. Although the upgrade page says that MHS pistols are not effected, regular P320 pistols and X-series pistols are effected. For details of the program, visit.
DISCONNECTOR SAFETY NOTIFICATION Daniel Defense is committed to the highest level of quality and safety. In keeping with that commitment we are issuing a safety notification related to a condition we identified with the Disconnector in the Fire Control Group. This safety notification applies to certain firearms manufactured between April 1, 2016 and March 3, 2017. In a few cases, a double fire condition has occurred with a single pull of the trigger.
In the Company’s spirit to always do the right thing, Daniel Defense will correct any and all potential conditions at no cost to the consumer as part of our 100% Satisfaction Guarantee. Does This Safety Notification Apply to My Firearm? Daniel Defense firearms containing a single-stage Fire Control Group, manufactured between April 1, 2016 and March 3, 2017, MAY fall within the scope of this. This is an important Safety Notification and should be followed by all owners of Daniel Defense firearms. IDENTIFICATION PROCESS. (The serial number is located on the left side of the lower receiver.). If your firearm’s serial number is indicated to be within the scope of this safety notification STOP USING THE FIREARM IMMEDIATELY and follow the Corrective Action Process below.